PHP 8.3.4 Released!

snmpset

(PHP 4, PHP 5, PHP 7, PHP 8)

snmpsetDéfinit la valeur d'un objet SNMP

Description

snmpset(
    string $hostname,
    string $community,
    array|string $object_id,
    array|string $type,
    array|string $value,
    int $timeout = -1,
    int $retries = -1
): bool

snmpset() sert à définir la valeur de l'objet SNMP spécifié par object_id.

Liste de paramètres

hostname

Le nom d'hôte de l'agent SNMP (serveur).

community

La communauté de lecture.

object_id

L'identifiant de l'objet SNMP.

type

Le MIB définit le type de chaque identifiant d'objets. Il doit être spécifié sous la forme d'un simple caractère depuis la liste suivante.

types
=Le type est récupéré depuis le MIB
iINTEGER
uINTEGER
sSTRING
xHEX STRING
dDECIMAL STRING
nNULLOBJ
oOBJID
tTIMETICKS
aIPADDRESS
bBITS

Si la constante OPAQUE_SPECIAL_TYPES a été définie lors de la compilation de la bibliothèque SNMP, les caractères suivants seront également disponibles :

types
Uint64 non-signé
Iint64 signé
Ffloat
Ddouble

La plupart de ces valeurs utilise le type ASN.1 correspondant. 's', 'x', 'd' et 'b' sont toutes des façons différentes de spécifier la valeur OCTET STRING et le type non-signé 'u' est également utilisé pour gérer les valeurs Gauge32.

Si les fichiers MIB sont chargés dans l'arbre MIB avec "snmp_read_mib" ou en les spécifiant dans la configuration de libsnmp, '=' pourra être utilisé comme paramètre de type pour tous les identifiants d'objets, vu que le type peut automatiquement être lu depuis le MIB.

Notez qu'il y a 2 façons de définir une variable de type BITS like i.e. "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":

  • En utilisant le type "b" et une liste d'octets. Cette méthode n'est pas recommandée vu que la requête GET pour un même OID retournera i.e. 0xF8.
  • En utilisant le type "x" et un nombre hexadécimal mais sans(!) le préfixe usuel "0x".

Reportez-vous à la section sur les exemples pour plus de détails.

value

La nouvelle valeur.

timeout

Le nombre de microsecondes depuis le premier timeout.

retries

Le nombre d'essais avant d'atteindre le délai maximal d'attente.

Valeurs de retour

Cette fonction retourne true en cas de succès ou false si une erreur survient.

Si l'hôte SNMP rejète le type de données, une alerte de type E_WARNING comme "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length." sera affiché. Si un OID inconnu ou invalide est spécifié, le contenu de l'alerte sera probablement "Could not add variable".

Exemples

Exemple #1 Exemple avec snmpset()

<?php
snmpset
("localhost", "public", "IF-MIB::ifAlias.3", "s", "foo");
?>

Exemple #2 Exemple avec snmpset() pour configurer l'identifiant de l'objet SNMP BITS

<?php
snmpset
("localhost", "public", 'FOO-MIB::bar.42', 'b', '0 1 2 3 4');
// or
snmpset("localhost", "public", 'FOO-MIB::bar.42', 'x', 'F0');
?>

Voir aussi

add a note

User Contributed Notes 4 notes

up
0
ch at lathspell dot de
14 years ago
Note that there are two ways to set a variable of the type BITS like e.g.:
SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}

1. Using type "b" and a list of bit numbers like:
snmpset('FOO-MIB::bar.42', 'b', '0 1 2 3 4');
with the disadvantage that the success is not easily verifyable as an snmpget() for the same OID would return e.g. 0xF8.

2. Using type "x" and a hex number but without(!) the usual "0x" prefix:
snmpset('FOO-MIB::bar.42', 'x', 'F0');
up
0
deivis dot jakstas at gmail dot com
17 years ago
If you setting hex values correct format is:
snmpset($source_ip,$community,"$oid","x","10 10 10 10");
up
0
slawrance at technologist dot com
24 years ago
The "type" parameter must be one of the following, depending on the type of variable to set on the SNMP host:

i INTEGER
u unsigned INTEGER
t TIMETICKS
a IPADDRESS
o OBJID
s STRING
x HEX STRING
d DECIMAL STRING
n NULLOBJ
b BITS

If OPAQUE_SPECIAL_TYPES was defined while compiling the SNMP library, the
following are also valid:

U unsigned int64
I signed int64
F float
D double

As an example, using "i" would set an integer, and "s" would set a string. If the SNMP host rejects the data type, you might get the following message: "Warning: Error in packet. Reason: (badValue) The value given has the wrong type or length."

If you specify an unknown or invalid OID, you might get a "Could not add variable" message. When specifying an absolute OID (one that is already resolved) that is completely numeric, prepend it with a period. For example, an OID that could enable/disable Ethernet ports on an Asante hub might be "1.3.6.1.2.1.22.1.3.1.1.3.6.4.0", but you would need to use ".1.3.6.1.2.1.22.1.3.1.1.3.6.4.0" in the OID parameter so that the SNMP library won't try to resolve an already resolved OID. Friendly, unresolved OIDs do not need the period prepended, such as "system.SysContact.0"
up
-6
tridman
16 years ago
If you have importet the MIB-Files into the MIB Tree with "snmp_read_mib" you may use '=' as the "type" parameter.
In this case the type will also be taken from the loaded mib file. (Octest strings will be interpreted like strings though)
Comes in handy for a more dynamic use of snmpset.
To Top