PHP 8.3.4 Released!

pclose

(PHP 4, PHP 5, PHP 7, PHP 8)

pcloseSchließt einen Prozess-Dateizeiger

Beschreibung

pclose(resource $handle): int

Schließt einen Prozess-Dateizeiger, der durch einen Aufruf von popen() geöffnet wurde.

Parameter-Liste

handle

Der Dateizeiger muss gültig und durch einen erfolgreichen Funktionsaufruf von popen() zurückgegeben worden sein.

Rückgabewerte

Gibt den End-Status des ausgeführten Prozesses zurück. Im Fehlerfall wird -1 zurückgegeben.

Hinweis:

Falls PHP mit der Option --enable-sigchild kompiliert wurde, ist die Rückgabe dieser Funktion nicht definiert.

Beispiele

Beispiel #1 pclose() Beispiel

<?php
$handle
= popen('/bin/ls', 'r');
pclose($handle);
?>

Anmerkungen

Hinweis: Nur unter Unix:

pclose() ist intern unter Verwendung des waitpid(3) Systemaufrufs implementiert. Um den wirklichen Exit-Statuscode zu erhalten, sollte die Funktion pcntl_wexitstatus() verwendet werden.

Siehe auch

  • popen() - Öffnet einen Dateizeiger für einen Prozess

add a note

User Contributed Notes 4 notes

up
13
Uwe Ohse
8 years ago
Regarding the return value:
"Returns the termination status of the process that was run. In case of an error then -1 is returned. "
and the note about the exit status: "pclose() is internally implemented using the waitpid(3) system call. To obtain the real exit status code the pcntl_wexitstatus() function should be used."

The documentation of the return value is, at best, misleading. The function returns, as does proc_close():
* -1 on error,
* WEXITSTATUS(status) if WIFEXITED(status) is true, or
* status if WIFEXITED(status) is false,
where status is the status parameter of waitpid().

This makes it impossible to differentiate between a relatively normal exit or a termination by signal, and reduces the value of the proc_close return code to a binary one (ok / something broke).

This can be seen in proc_open_rsrc_dtor() in ext/standard/proc_open.c (PHP 5.4.44, 5.6.12).

The note advising the use of pcntl_wexitstatus is plain wrong. One cannot use pcntl_wexitstatus because it already has been used.
up
3
kcross at nssolutions dot com
20 years ago
Somewhere between 4.1.1 and 4.2.3, the return value from pclose changed.

The exit status used to be in the second byte, so that the status would be (pclose($fp)/256).

It is now in the low-order byte, so the status is just pclose($fp).

Be careful.
up
2
vdweij at mailsurf dot com
21 years ago
As I understand pclose will return 0 (on every platform) in case popen could not execute the specified command.

Since popen only returns the status wether it was able to send a command and not wether it was succesfully executed. Only the returned value of pclose can be used to check wether a command could be executed.
up
1
Mike
15 years ago
The termination status, as pointed out in another note, is not the same as the exit status from the process. However, something like "pclose($fp)/256" is not the correct way to extract the exit status, since this uses system- and version-specific knowledge of where in the termination status the exit status is stored. (Also, the process may not even have exited normally, so it may not have an exit status at all.)

Instead, the functions pcntl_wifexited() and pcntl_wexitstatus() should be used. They are wrappers for the C macros WIFEXITED() and WEXITSTATUS() that are designed for determining whether the process had an exit status and what that status was, respectively.
To Top